UEU-co logo

Posts Tagged ‘Remote Access’

Sams Teach Yourself Windows® Server 2008 in 24 Hours by Joe Habraken Publisher: Sams Pub Date: May 14, 2008 Print ISBN-10: 0-672-33012-1 Print ISBN-13: 978-0-672-33012-4 eText ISBN-10: 0-7686-8080-8 eText ISBN-13: 978-0-7686-8080-5 Pages: 648 Table of Contents | Index Copyright About the Author Acknowledgments We Want to Hear from You! Reader Services Introduction Part I: Server Installation […]

Introduction Selecting and deploying a network operating system is one of the most important tasks shouldered by a network administrator. In this book, I wanted to put together a body of information related to the newest version of Microsoft’s powerful network operating system platform—Microsoft Windows Server 2008—that would not only highlight the functions and capabilities […]

Sams Teach Yourself Windows® Server 2008 in 24 Hours by Joe Habraken Publisher: Sams Pub Date: May 14, 2008 Print ISBN-10: 0-672-33012-1 Print ISBN-13: 978-0-672-33012-4 eText ISBN-10: 0-7686-8080-8 eText ISBN-13: 978-0-7686-8080-5 Pages: 648 Table of Contents | Index Overview In just 24 lessons of one hour or less, you will be able to install and […]

Configuring NAT on the Server As mentioned in Hour 18, the Routing and Remote Access Services (RRAS) are added to a server when you add the RRAS role in the Add Roles Wizard. (Open the Add Roles Wizard via the Initial Configuration Tasks window or the Server Manager.) When RRAS is enabled in the Routing […]

Hour 22. Using Network Address Translation and Certificate Services What You’ll Learn in This Hour: Using Network Address Translation Configuring NAT on the Server Understanding the Active Directory Certificate Services Adding the Active Directory Certificate Services Configuring the Certificate Authority Requesting Certificates Managing the CA Hour 17, “Remote Access and Virtual Private Networking,” took a […]

Hour 22. Using Network Address Translation and Certificate Services What You’ll Learn in This Hour: Using Network Address Translation Configuring NAT on the Server Understanding the Active Directory Certificate Services Adding the Active Directory Certificate Services Configuring the Certificate Authority Requesting Certificates Managing the CA Hour 17, “Remote Access and Virtual Private Networking,” took a […]

Enabling Routing and Remote Access Before you can configure RRAS (more specifically, routing), you must enable the service. You can enable (and then configure) RRAS via the Server Manager or the RRAS snap-in running in the MMC. Follow these steps: 1. In the Server Manager, expand the Roles and Network Policy and Access nodes and […]

Understanding and Configuring the DHCP Relay Agent Before we leave this discussion of routing, we should discuss issues related to running DHCP in environments where either remote clients (as discussed in the previous hour) receive their IP addresses from a DHCP server or you have a subnetted IP network that uses DCHP. Both these problem […]

Configuring IP Routing After you have your server’s network interfaces configured with the appropriate IP addresses and RRAS is enabled, you can configure the server for routing IP. Routing can be handled in two different ways: static routing and dynamic routing. As already mentioned earlier in the hour, static routing requires that routing information be […]

Configuring Network Interfaces Because the RRAS-enabled server is to serve as a router between two segments of the network, you need to configure the network interfaces on the server with the appropriate fixed IP addresses. The IP address for each network interface is dictated by the range of IP addresses that you are using for […]

Configuring Authentication You can select the type of remote access authentication that you want to use on your RAS server. To configure the authentication protocol (or protocols) supported by the RAS server, follow these steps: 1. In the Routing and Remote Access snap-in, right-click the server icon in the tree and select Properties from the […]

Configuring Modem Ports When the RRAS service is started for the first time, it creates ports for any modems that are installed on the server. You must configure these modem ports to allow remote client connections. To configure a modem port, follow these steps: 1. In the Routing and Remote Access snap-in, click the server […]

No related posts found…

Categories

apply_now Pepperstone Group Limited